Dish network satellite installation instructions

Never mount to a tree or a public utility pole. Align the top part of the mast so that it is absolutely vertical. If the top part of the mast is off vertical by only a few degrees, it will be difficult or maybe even impossible for you to find the satellites. Take at least two readings with a level, on the upper mast, that are 90 degrees apart from one another.

Loosen both skew bolts and set the skew by rotating the dish mounting bracket to align the mark with the required angle on the skew scale which you wrote above. Tighten the skew bolts securely. See Table 1 for the required torque values. After the skew is set, do not try to finetune the skew angle when aiming the dish. Grounding, other devices, and in-home cabling must also meet these requirements.

RG-6 coaxial cable rated for at least to MHz must be used in this installation. Do not use existing cables such as RG as it may cause signal loss. Also, be sure that any outdoor connections are made using waterproof F-connectors rated for MHz or greater. The cable length between the DISH Damage caused by over-tightening is not covered by the limited warranty. Tighten all indoor coaxial cable connections to the receiver only by hand. If you use a wrench, you may over-tighten the connections and damage your equipment.

Connect a temporary cable to a peaking meter. Thread the other end of the cable through the LNBF arm and bracket. Attach the LNBFs to the bracket using the included screws. Do not adjust the skew. Ensure you are peaking the dish using transponder 11 or higher.

With the peaking meter still connected, tighten the mast clamp and elevation bolts using the torque values listed in Table 1 on page 6. Re-confirm signal strength after tightening the bolts. Remove the temporary cable used for peaking the dish. Thread the cable s from the receiver s through the LNBF arm and bracket.

Connect a cable from DPP If a Legacy receiver is present, it should be installed last. Connect a cable from the DPP A splitter or other device will not work in this configuration. If you use a wrench, you may over-tighten the connections and damage your equipment Connect the receiver s to the TV s and display the Point Dish screen if not shown, for most receivers, press MENU on the remote control. Join Our Mailing List.

Email Address:. Website design by Solid Cactus. Join Our Mailing List Get our best deals delivered to your inbox. Keep hammering until the bolt is flush with the wall. Then, repeat this with the remaining bolts. Make sure the bolts are level with the wall, or else the dish's mount won't anchor properly. Place the metal plugs and hammer them into the wall.

Your dish will come with a set of plugs that serve as wall anchors. Position them, so their open end faces out from the wall.

That opening is for bolting the wall mount in place. After pushing the plugs into the holes, tap them in with a hammer and chisel. They are what anchors the mount to the wall or ceiling. If they are loose, your dish could end up crashing to the ground! Bolt the mount onto the plugs in the wall. Position the mount back on the wall, lining up the plate's holes with the pilot holes you drilled.

Fasten the bolts by using a cordless screwdriver. Make sure the mount feels secure in the wall before you move on. If you're sure they are in correctly, take them out and recheck the plugs. Cap each bolt with a metal washer and locking nut. These components prevent the bolts from coming back out of the wall. Slide the washers on first, which are flat metal disks that help the nuts work properly. Then, add the nuts and turn them clockwise with a wrench until they feel tight and no longer move.

Be careful not to overtighten the nuts. Stop twisting them when they become hard to move. As long as they are not loose, the mount will also stay in place. Part 2. Attach the antenna bracket to the low noise block LNB arm. Your dish will most likely come with a flat metal plate to connect the satellite dish to the L-shaped LNB arm and other components.

Position the plate, so the prongs are on the left and right, facing you. Hold the LNB arm between the prongs with the tail end extending out past the plate's opposite side. The exact installation process, including the bolts' size, may vary a little depending on the dish you have. Refer to the owner's manual for more specific instructions. Clip the antenna adjustment panel over the plate's prongs. The panel will look like a square box with one end open.

Add a washer and nut on the end of each bolt after tightening them. This slot is what you use to point the satellite up or down. Fit the U-shaped rod inside the adjustment panel. Your dish will have a bent metal rod that fits into one of the slots on the adjustment panel. Slip the rod inside, sliding its prongs through the holes. Ensure the prongs point toward you rather than the tail end of the LNB rod you connected earlier.

Fit a small clamp over it, followed by a washer and nut on each prong. The adjustment panel has 3 different slots. Use the slots to reposition the satellite dish. In most cases, the middle slot is best for setting the dish at the proper angle. Bolt the antenna bracket to the back of the satellite dish. You have a couple more bolts to add to finish the bulk of the assembly, and this is one of the easiest parts to finish.

Line up the holes on the plate with the holes on the back of the dish. Stick the longest bolts you have, usually 2 to 3 in 5. Then, place a washer and nut on the end of each bolt, tightening it with your wrench.

If they feel shaky, carefully separate them and tighten the bolts. One last component, the LNB, controls the dish's functionality. First, slide the handle of the LNB onto the open end of the arm.

Secure it with nuts and bolts, then take the LNB out of the box. It looks almost like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place. You may need to loosen the LNB later to readjust it and improve the signal quality. Connect the adjustment panel on the dish to the wall mount. Fit the dish onto the open end of the support.

If everything is attached correctly, it will fit inside or behind the adjustment panel. You can then add the 1 or 2 remaining bolts to fasten these pieces together. If the dish looks good, then you're ready to position it to communicate with a satellite.

If the mount is meant to attach to the back of the panel, your satellite will also come with a pair of clips. Position them behind the support, then add the screws through them to bind the parts together.

Part 3. Select a satellite you wish to connect to. Pick a satellite that is in range of your particular dish. There are numerous satellites out there, but dishes cannot get signals from all of them. If you bought your dish from a TV service, for instance, you might have a hard time connecting to their competitor's satellites. Tracking sites list the names, which usually include the owning company or the service they provide.

If you bought a satellite service, it is possible to receive satellite signals outside that service. Since you usually need to replace several parts, it's easier to get a new satellite instead. Try to pick a satellite close to your area. If you subscribe to a particular TV service, you will need to use the company's satellites. The biggest providers have multiple satellites. Find the satellite's location before positioning the dish.

You're going to need to point the dish in the correct direction, then angle it up at the sky. This isn't easy to do if you don't know the satellite's positioning. Fortunately, satellites don't move much, so you can use a positioning database to adjust your dish. The site will give you the precise positioning needed for your dish to receive the signal. You won't be able to receive a signal from a distant satellite. Don't expect to reach a Chinese satellite if you're in North America, for instance.

Use the azimuth number to rotate the satellite. Have a compass handy and locate true north first. Then, look at the azimuth number and find where that is on the compass. North is considered 0 degrees, east is 90 degrees, south is degrees, and west is degrees.

Rotate the satellite dish horizontally until it points in the correct direction. Then, turn the satellite southwest from there. Move the dish vertically to adjust its elevation. Once you know the height needed to reach the satellite, go behind the dish. Examine the end of the mount where it connects to the dish. You will see a bolt inside a slot labeled by degrees, usually 10 to Loosen the bolt by twisting it counterclockwise, then reposition the dish to the proper elevation.

Moving the bolt along the slot raises or lowers the dish. For instance, if the dish requires a degree elevation, it will point up into the sky almost as much as it possibly can. Slide the loosened bolt back toward the degree marker. Adjust the dish's polarization until you get a clear signal. The final part that needs to be adjusted is LNB, responsible for receiving and sending the signal into your home.

It is usually an arm on the front that points toward the dish. Test out the signal quality by hooking the dish up to the receiver and a TV, then loosen the connecting nut on the arm by turning it counterclockwise with a wrench. If the TV is far away, have someone else stand near it and give you feedback. You may need to wait to adjust the LNB until you're done with the wiring.

Take care of it before then, if you're able, so you don't have to keep climbing on the roof to make adjustments. The LNB can sometimes be controlled by turning a mount part on the back of the dish left or right. Part 4. Check your home first for a previously-used cable opening. The dish's cable needs its own little space to enter your home and hook up to your TV. Unless your home is in the process of being built, drilling a single hole is the easiest way to do this.

Position your TV and the satellite receiver nearby to prepare for the connection. It needs to be below the frost line, the lowest point that freezes in winter, which is about 3 in 7. Run a coaxial cable from the LNB to the receiver. Make sure the receiver is positioned close to the satellite to ensure the cable can reach it. TV service providers will also give you one when you buy a satellite from them. The coaxial cable sometimes connects to the back of the satellite. Usually, though, it plugs directly into the LNB.

Once the cord is in place, your TV will be able to receive the satellite signal.